Differences between revisions 4 and 5
Revision 4 as of 2007-02-09 20:11:01
Size: 7498
Revision 5 as of 2007-02-09 21:48:38
Size: 7495
Deletions are marked like this. Additions are marked like this.
Line 3: Line 3:
'' To know where to begin, make sure you have read the [:FoxTutorials: tutorials first !]'' '' To know where to begin, make sure you have read the [:Tutorials: tutorials first !]''

Graphical Interface for Powder Pattern Diffraction data

To know where to begin, make sure you have read the [:Tutorials: tutorials first !]

  • [#menus Menus]
  • [#radiation Radiation]
  • [#sithsl Max sin(theta)/lambda]
  • [#backgd Background description]
  • [#crystal Crystalline phase: PowderPatternDiffraction]



Powder Menus

  • "Data" allows to import several types of data. If you wish to add another format, send me an email with an example data, and saying why you think it is important that this format is supported. You can also save the calculated and observed spectra, and use the 'simulation mode', which will use a dummy observed pattern (I=1. in all points).

  • "Parameters" allows you to fix all parameters. Note that only preferred orientation parameters and the global temperature factor are refinable anyway.

  • "Components" is the menu to describe your powder pattern in terms of the sum of components, which can be one interpolated background, and any number of crystalline phases.

  • "Radiation" allows you to choose the radiation for your experiment. It is also possible to use the radiation interface just below the menus, but to choose an X-Ray tube it is easier that way (unless you know by heart the delta-lambda !). Do not forget to input the correct polarization rate (typically 0.95 for a synchrotron experiment, and 0 for a laboratory diffractometer without monochromator).

  • "Pattern" allows you to open the graph window with the observed and calculated patterns, and to fit the scale factor. It is also possible to add "excluded 2-theta zones" which will be ignored during global optimization: you will be prompted for the minimum and maximum 2theta values of the region to ignore (to remove those regions, you have to edit the xml file).



Here you can describe the radiation corresponding to your experiment (neutron, X-Ray, tube,...). The wavelength is in Angstroem as usual. Set the polarization rate between 0.95 and 1 for synchrotron experiments, and 0 for an X-Ray tube (actually if you use a monochromator it should be above 0, but a precise value is not critical for a global optimization).

You can also select Neutron Time Of Flight. You will need to enter the DIFA and DIFC parameters corresponding to the instrument the data was recorded on.


2theta correction parameters

These parameters allow to correct for experimental errors in the 2theta positions of reflections, due to a wrong zero, or a misplacement of the sample holder or its transparency. For most data sets, using the 2theta zero is sufficient. After each change, you can right-click on the powder pattern graph to update it.You should always check that all peaks are correctly and precisely indexed before launching an optimization.


Maximum sin(theta)/lambda

Use this field to limit the extent of the calculations on the powder pattern. It is usually a very good idea to do that, since for a global optimization, high-angle data is useless. A good value is 0.25 Angstroem-1 (corresponding to a resolution of 2 Angstroems), although you can go higher to 0.4 A-1 if you feel there are not enough reflections...


Powder Pattern Background

The background can be modelized using either linear or [http://en.wikipedia.org/wiki/Cubic_spline cubic spline] interpolation between user-chosen 2theta (or tof) values. The easiest way to create the background is to use the automatic Bayesian (Sivia-David) background estimation: use the "Components->Add Bayesian Background (automatic". You will be prompted to choose the number of interpolation points (10 to 20 should be OK, depending on how much structure there is in the background). FOX will then spend a few seconds finding the best background

To input the (2theta, intensity) points you can also create a text file with a list of "2theta intensity" on each line (2theta in degrees), and load it using the menu.

If you want to change the points (either the intensity or the position), just edit the values in the grid.

There is currently no limit to the number of points, but even for complex backgrounds 20 should be enough.


PowderPatternDiffraction: Crystalline phase contribution to the powder pattern

This allows to describe the contribution of a crystalline phase to the powder pattern. It is possible to save the calculated structure factors using the menu (note that structure factors above the chosen sin(theta)/lambda limit are not calculated).

  • Profile parameters: using the "profile" menu, you can use the following models:

    • Pseudo-Voigt, for constant wavelength experiments (either x-ray or neutrons). The follwong parameters are available:

      • U, V, and W define the width using Caglioti's law (W is the constant width, which is generally sufficient if you are using integrated Rfactors as recommended). fwhm=[W+V*tan(theta)+U*tan2(theta)]0.5

      • Eta0 (constant) and Eta1 (theta-dependant) define the mixing parameter for a pseudo-Voigt profile (eta=eta0+eta1*2theta), eta=1 corresponds to a pure Lorentzian and eta=0 to a pure Gaussian.

      • Asym0 (constant),Asym1 and Asym2 (theta -dependant): asymmetry parameters (ratio between intensities on the left and right of the reflection maximum): asym=A0+A1/sin(2theta)+A2/sin2(2theta)

    • Double-exponential pseudo-Voigt: for neutron time-of-flight data.

  • Crystal choice: you are asked to choose a crystal structure upon creation of the PowderPatternDiffraction object. You can change it afterwards by clicking on the crystal name.

  • Global Biso: this can be used as a global temperature factor for this crystalline phase (affects all atoms). This is refinable, although it slows the optimization without helping a lot (it is therefore not recommended at all to optimize it !).

Texture (Preferred Orientation) using the March-Dollase Model

FOX supports optimization of Preferred orientation, usign the March-Dollase model. To add one phase, use the "Phases" local menu. You can then enter the fraction, March coefficient (>1 for needles, <1 for plate-like crystallites), and HKL coordinates for the preferred orientation.

Note: it is very important to use this only as a last resort, or if you know for sure that you have preferred orientation. Taking one more day to prepare carefully a non-textured sample is definitely worth it, since even if a solution is found, it will take much longer - preferred orientation reduces the information available in some direction of the crystal.

If you finally decide to search for preferred orientation parameters, you must input as much information as possible: you should be able to know what kind of preferred orientation to expect (plates or needles), so that you can restrict the March coefficient to be either >1 or <1 (e.g. use limits [.5;1] or [1;2] - never go below .1 or above 10, that would just slow things). If you know what the preferred orientation vector is, that's even better.

Note that it is possible to use several preferred orientations, but I strongly discourage to do this for a global optimization.

None: Manual/Powder (last edited 2019-03-22 13:02:49 by VincentFavreNicolin)